update

docs/en/guide/pve/pve_kvm.md

@@ -217,6 +217,11 @@ Two versions are available, choose as needed.
 Before use, ensure that the current host machine has at least 2 available IP addresses within its IP range, and there are unallocated IP addresses. These unallocated IP addresses should not be bound to the host machine.
 :::
 
+:::tip
+At this point, the IPV4 address appended is the address following the host's current IPV4 address in sequence.
+For example, if the current host address is ```1.1.1.32``` and then ```1.1.1.33``` there is already a virtual machine, then this script appends an IP address of ```1.1.1.34```.
+:::
+
 - Automatically detect available IP ranges. Use ping to identify unallocated IP addresses and select one to bind to the virtual machine.
 - If the host machine has an accompanying IPv6 subnet, there will be an option to attach an IPv6 address.
 - Relevant system information will be stored in the corresponding virtual machine's NOTE section, accessible for viewing on the web interface.
@@ -268,12 +273,13 @@ The above command is used to create a virtual machine with a dedicated IPv4 addr
 - If the vendor has provided an IPV4 address and subnet length, please carefully compare and write the parameters in the command format shown below.
 - Relevant system information will be stored in the NOTE of the corresponding virtual machine and can be viewed on the WEB end.
 - Optionally enable or disable standalone IPV6, requires the host to have at least one /64 subnet.
-- The manually appended IPV4 address is in a **different subnet** from the host's IPV4 address (different IP address prefixes)
+- Manually appended IPV4 addresses that are in **different subnets** from the host's IPV4 address (different IP address prefixes) will use the host's IP address as the gateway
+- Manually appended IPV4 addresses that are within the **same subnet** as the host's IPV4 address (same IP address prefix) will use the host's gateway as the gateway
 - Optionally specify the MAC address of the virtual machine
 
 :::tip
-If the router does not recognize the source MAC address, the traffic will be flagged as "abuse" and "may" cause the server to be blocked.
-(If using Hetzner's stand-alone servers be sure to provide the MAC address that corresponds to the additional IPV4 address to prevent abuse from being reported.)
+If IP addresses within **different subnets** are appended without a MAC address, the router will not recognize the source MAC address, and the traffic will be flagged as “misuse” and “may” cause the server to be blocked.
+(If you are using a Hetzner standalone server, it is recommended that you provide the MAC address of the attached IPV4 address to prevent abuse from being reported.)
 :::
 
 #### Usage Instructions

docs/guide/pve/pve_kvm.md

@@ -245,7 +245,12 @@ PVE修改VM配置前都得停机先，再修改配置，修改完再启动，免
 ### 自动选择IPV4地址无需手动指定的版本
 
 :::warning
-使用前需要保证当前宿主机的IP段带了至少2个IP，且有空余的IP未配置，该空余的IP未绑定宿主机
+使用前需要保证当前宿主机的IP段带了至少2个IP，且有空余的IP未配置，该空余的IP未绑定宿主机。
+:::
+
+:::tip
+此时附加的IPV4地址是宿主机目前的IPV4地址顺位后面的地址，
+比如目前宿主机地址是```1.1.1.32```然后```1.1.1.33```已经有虚拟机了，那么本脚本附加IP地址为```1.1.1.34```
 :::
 
 - 自动检测可用的IP区间，通过ping检测空余可使用的IP，选取其中之一绑定到虚拟机上
@@ -306,12 +311,13 @@ curl -L https://cdn.spiritlhl.net/https://raw.githubusercontent.com/oneclickvirt
 - 如果商家有给IPV4地址和子网长度，请仔细比对，按照下面示例的命令写参数
 - 系统的相关信息将会存储到对应的虚拟机的NOTE中，可在WEB端查看
 - 可选择是否开启独立IPV6，需要宿主机至少有一个/104的子网，最好是一个/64子网
-- 手动附加的IPV4地址与宿主机的IPV4地址是在**不同子网**内的(IP地址前缀不同)
+- 手动附加的IPV4地址与宿主机的IPV4地址是在**不同子网**内的(IP地址前缀不同)，将使用宿主机IP地址做网关
+- 手动附加的IPV4地址与宿主机的IPV4地址是在**同一个子网**内的(IP地址前缀相同)，将使用宿主机的网关做网关
 - 可选择是否指定虚拟机的MAC地址
 
 :::tip
-如果路由器无法识别源 MAC 地址，流量将被标记为“滥用”，并“可能”导致服务器被阻止。
-(如果使用Hetzner的独立服务器务必提供附加IPV4地址对应的MAC地址防止被报告滥用)
+在**不同子网**内的IP地址，如果附加时不指定MAC地址，那么路由器无法识别源 MAC 地址，流量将被标记为“滥用”，并“可能”导致服务器被阻止。
+(如果使用Hetzner的独立服务器务建议提供附加IPV4地址对应的MAC地址防止被报告滥用)
 :::
 
 #### 使用方法